Women's Tops/Bandeau Top Sewing Pattern PDF | Strapless Tube Top | Y2K Crop Top | Womens Summer Beachwear | XS-M
1 / 5Interactive sewing map
Step-by-step technological process of sewing the garment.
1
Page 2
Trimming the dart seam allowance
- Trim the dart seam allowance along the marked line on the front piece and the front lining.
3
Page 2
Sewing the darts
- Sew the darts on the front piece and on the front lining.
4
Page 2
Marking the dart seam allowance
- Mark the dart seam allowance cut line, keeping it parallel to the stitching and 1.0 cm away.
5
Page 3
Pressing the side seams
- Press the side-seam allowance toward the back.
6
Page 3
Pinning the lining side seams
- Pin the side edges of the front lining and back lining together, matching the edges and placing right sides facing each other.
7
Page 3
Stitching the side seams
- Stitch and serge the side seams of the front and back at the same time on a 4-thread overlock. Seam allowance: 0.7 cm.
8
Page 3
Pinning the side seams
- Pin the side edges of the front and back pieces together, matching the edges and placing right sides facing each other.
9
Page 4
Sewing the lining side seams
- Sew the side seams of the front and back lining pieces, leaving a 4–5 cm opening in one side seam. Seam allowance: 0.7 cm.
10
Page 4
Pressing the lining side seams
- Press the side-seam allowance toward the front lining.
11
Page 4
Pinning the top elastic
- Pin the elastic to the top edge of the top, placing it from the upper side and spreading it evenly along the full length, overlapping the elastic ends by 1.0 cm.
12
Page 4
Pinning the top to the lining
- Pin the outer top to the lining along the upper edge, matching the raw edges and side seams, with right sides facing each other.
13
Page 5
Finishing the top edge
- Finish the top edge of the top with the lining, while simultaneously stitching on the elastic all the way around using a 4-thread serger. Tuck the overlock thread tails into the cover-stitching line using a hook.
14
Page 5
Pinning the bottom edge
- Place the lining and the top together with wrong sides facing. Pin the lower edge of the outer top to the lining edge, turning a small section so the right sides face inward. Pin the edges through the open section at the hem.
15
Page 5
Pressing the top edge
- Turn right side out and press the top edge of the top, forming a slight roll from the front and back outer pieces.
16
Page 6
Pressing the bottom edge
- Press the bottom edge of the top, forming a slight roll to the inside from the outer fabric on the front and back pieces.
17
Page 6
Serging the bottom edge
- Serge the lower edge of the top shell to the lining edge on a 4-thread overlock, gently stretching and smoothing the seam allowances all the way around. Use a hook to tuck the serger thread tails into the coverstitch line.
18
Page 6
Turning the top right-side out
- Turn the top right-side out through the opening left in the lining’s side seam.
19
Page 7
Threading the bottom elastic
- CUT A 2.0 CM-WIDE ELASTIC TO THE REQUIRED LENGTH. THE RECOMMENDED ELASTIC LENGTH IS INDICATED ON THE FRONT PATTERN PIECE. THREAD THE ELASTIC INTO THE CASING THROUGH THE OPENING LEFT.
20
Page 7
Marking the casing line
- MARK THE CASING TOPSTITCH LINE ALONG THE BOTTOM EDGE OF THE TOP, SETTING IT 2.2 CM IN FROM THE EDGE.
21
Page 7
Securing the elastic ends
- SECURE THE ELASTIC ENDS BY OVERLAPPING THE CUT EDGES BY 1.0 CM. MAKE SURE THE ELASTIC INSIDE DOESN’T GET TWISTED!
22
Page 7
Topstitching the casing
- TOPSTITCH ALONG THE MARKED CASING LINE, LEAVING A 2.0 CM OPENING AT THE SIDE SEAM AREA.
23
Page 8
Closing the casing opening
- Stitch closed the opening left in the casing’s side seam section.
24
Page 8
Closing the lining opening
- Hand-sew the opening left in the lining’s side seam using invisible stitches.
